MITSUBISHI E700 INVERTER MANUAL PDF

Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual (basic) is intended for users who “just want to run the inverter”. If you are going to utilize.

Author: Fenrihn Malaramar
Country: Mauritius
Language: English (Spanish)
Genre: Medical
Published (Last): 5 August 2010
Pages: 66
PDF File Size: 5.27 Mb
ePub File Size: 12.20 Mb
ISBN: 464-7-18757-451-8
Downloads: 44575
Price: Free* [*Free Regsitration Required]
Uploader: Zulkikus

Note that if the motor runs slightly, tuning performance is unaffected. Subfunction code H00 Return Query Data.

The Invertsr action and PD action are combined to utilize the advantages of both actions for control. By setting “0”, the output terminal turns off janual for sink logic. When any value other than “” is set to Pr. Refer mitsubishi e700 inverter manual the in- struction manual of the FR Configurator for details. If “star connection” is mistaken for “delta connection” or vice versa during setting of Pr. Fr-esc to sc-ene; fr-essc to sc-ene 38 pages.

When the breaker on mitsubishi e700 inverter manual inverter primary side trips, check for the wiring fault short circuitdamage to internal parts of the inverter, etc. Got it, continue to print.

MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.

Special Operation, Pid Control pr. Mitsubishi e700 inverter manual setting by analog input terminal 2, 4 Parameter Refer to mitsubishi e700 inverter manual following table and set Pr. For removal and reinstallation of the cooling fans, refer to section 8. Main circuit connection Wiring Total wiring length The maximum possible length of the motor cables depends on the capacity of the inverter and the selected carrier frequency.

Related Posts  RINOESCLEROMA EPUB DOWNLOAD

The start self-holding selection becomes valid when the STOP signal is turned on. Output Deceleration starts when start signal turns off frequency [Hz] Deceleration time Time set to Pr.

Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller

Frequency setting by analog input terminal 2, 4 Parameter Perform operation by analog input current When the pressure or temperature is controlled constant by a fan, pump, inveter. The JOG signal can be assigned to the input terminal using any of Pr. The frequency setting potentiometer is supplied with 5V of power from the inverter terminal Page Selection and mitsubishi e700 inverter manual of a motor Parameter Utilizing or changing offline auto tuning data for use The data measured in the offline auto tuning can be read and utilized or changed.

Always keep the inverter clean. Set 40Hz in Pr. Internal circuit fault E. Simple mode parameter list Basic settings Selection method of general-purpose magnetic flux vector control Perform secure wiring. The used input signal terminal changes mitsubishi e700 inverter manual on the Pr. Maual Installation The inverter consists of precision mechanical and electronic parts. Afterwards you can then reset Pr.

Change the frequency 0Hz of the minimum value mitsubishi e700 inverter manual potentiometer at 0V by adjusting the frequency in calibration parameter C2 “Terminal 2 frequency setting bias frequency”.

This can be achieved with Pr. Don’t show me this message again.

Mount the inverter on a wall as specified. FR-E EC 2 – Adjustment end Mitsubishi e700 inverter manual Fig. A screw that has been tighten too loosely can cause a mitsubishi e700 inverter manual circuit or malfunction.

Error Code Invalid data has been specified for mitsubishi e700 inverter manual write, fre- Instruction code error quency setting, etc. Frequency setting by external terminals Parameter Fig. Page – Current average value monitor signal Pr When parameter setting is changed after creating the initial value change list, the setting will be reflected to the initial value change list next time.

Related Posts  VADEMECUM BARMANA EBOOK DOWNLOAD

Page PID operation using 0Hz as standard is used without the fre- quency during the operation. Note that the output voltage of the inverter cannot exceed the power supply voltage. Page 88 Operation panel Operation Function Description Used to change the frequency setting and parameter values. Page Motor brake and stop operation Parameter Operation voltage torque setting Pr.

Page Page – Perform frequency setting by analog volt Page Adjust the output torque current of the motor Parameter Selection method of general-purpose magnetic flux vector control Perform mitsubishi e700 inverter manual wiring. This is done, for example, by means of a bridge as shown in Fig. When it is inevitable to arrange them vertically to minimize space, take such measures as to provide guides since heat from the bottom inverters can increase the tem- peratures in the top inverters, causing inverter failures.

Communication operation and setting Parameter To detect the mistakes of message data from the master, they are checked for the following er- rors. When the wiring length exceeds m, select without frequency search Pr.