ANIXTER WIRE & CABLE TECHNICAL INFORMATION HANDBOOK PDF
This handbook is designed to be a useful collection of engineering and technical information on electrical and optical wire and cable and related products. Anixter Wire & Cable Technical Information Read more about conductor, cables, electrical, conductors, voltage and resistance. View Anixter Cable from ENG 1 at Tsinghua University. WIRE AND CABLE TECHNICAL INFORMATION HANDBOOK $ HARDBOUND $
|Published (Last):||25 December 2005|
|PDF File Size:||17.32 Mb|
|ePub File Size:||12.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
A transmission control character used to indicate the end of transmission, which may include one or more texts and any associated message headings. Both constructions have inherent advantages. This characterizes the installed system with regard to near-end crosstalk, attenuation and impedance. HDPE — High density polyethylene.
Aluminum 1 Outside diameter—1. PCS plastic clad silica fiber, with a glass core and plastic cladding, and all-plastic fibers are available for special applications. In addition, a basket grip should be applied over the conductors to prevent any slippage and to facilitate guiding the conductors through the pulleys. Boosting generators are also used to raise the level of a DC line. A seven bit plus parity code established by the American National Standards Institute to achieve compatibility among data services and consisting of 96 displayed upper and lower case characters and 32 nondisplayed control codes.
Attenuation is the parameter most frequently measured and infornation the attenuation tecnical the cable as well as that of attached connectors. Continental Europe Velocity of propagation is expressed as a percentage of the speed of light.
Anixter Wire & Cable Technical Information Handbook
Plastic tip connectors offer a low cost solution when loss is not critical. These include publications uandbook It can include wire with a steel core, plated, or coated wire.
ETFE — Ethylene tetrafluoroethylene. Conversion Tables It will resist wear, cutting, and impact. The voltage standing-wave ratio VSWR is a measure of the standing waves that result from reflections. Normally this requires infomation a few seconds unless cable circuits of high capacitance are involved. Thermocouple wire or extension grade wire is recommended for use in connecting thermocouples to the sensing or control instrumentation.
Because of its dire design and latching, the SC subscriber connector can be arranged in very high density patching systems. The National Electrical Code is divided into approximately articles.
The cables do not contain a white or green conductor.
The term is loosely used to also include coupling at higher frequencies. Also known as Splicing loss and Transfer informaation. ALS — A type of cable consisting of insulated conductors enclosed in a continuous, closely fitting aluminum tube. All wire and cable has a minimum safe bending radius.
The older types are no longer standard in the industry. When pulls are relatively light a basket-weave grip is often used. The standard unit used to express the relative strength of informstion signals. Connect the cable ends to a dry nitrogen or dry air supply using hoses, valves, fittings, and flow regulators as shown in Figure 8. To convert in the reverse direction, divide by the factor given in the table.
Types of Coaxial Cables. Filling compounds may require heating or mixing prior to filling. The short circuit current is the maximum allowable current that the cable can withstand without damage. Produces the highest EMF per degree of any standardized thermocouple. Hook up Red Color-Coded wire to negative terminal of instrument. The tight interface of the threads, especially when subjected to vibrations, allows the connector to maintain a low VSWR up to 11 GHz with flexible cable and up to 15 GHz with semirigid cable.
HARNESS — An arrangement of wires and cables, usually with many breakouts, which have been tied together or pulled into a rubber or plastic sheath, used to interconnect an electric circuit.
Wire and Cable Technical Information Handbook: Anixter: : Books
One of the control signals on a standard RSC connector. NBN Armored, polyethylene insulated cables for telephone networks.
Below are listed some of the most common high temperature wire and cable types along with their temperature rating: Tests which prove the wire or cable meets the specified requirements must be conducted by the manufacturer and must be carefully documented. This cable contains two individual coaxial cables surrounded by a common outer jacket. In a compact conductor each wire is preformed into a trapezoidal shape before the wires are stranded together into a tchnical conductor.
Anixter Wire & Cable Technical Information Handbook
Navy introduced the MIL-C cable specification. Multiply inches by 1, to calculate mils. Generally, conductor size on long, low-voltage lines is governed by voltage drop; on short, high-voltage lines by heating.
Humidity also increases the termination leakage current, which is included in the total leakage current.
Loose Buffer Two different types of cable construction are generally employed to contain the optical fibers. Fiber Optic Cables Minimum bending tehcnical for fiber optic cable is ten times the cable diameter for multimode and 20 times the cable diameter for single mode. Showing of 1 reviews.